The email address entered is already associated to an account. What is voltage on – button? Instant Repair Help over the Phone 6ya. The inductors all show less than 1 Ohm taken in-circuit so they’re probably not open-circuit? If anyone knows different though, let me know and I’ll change it!

Uploader: Shakami
Date Added: 24 February 2017
File Size: 61.1 Mb
Operating Systems: Windows NT/2000/XP/2003/2003/7/8/10 MacOS 10/X
Downloads: 4384
Price: Free* [*Free Regsitration Required]

Please enter a valid email address. More Print this page Share this page. Page 2 of 2. Cjv by davidb on May 06, A second manual had schematics, but they were wrong, and they actually appeared to correspond to the Viewsonic monitor same numbers Besides, they were not in vector format and all component values were unreadable So, I figured I might as well try to draw one myself for the button circuitry – it is attached below The schematic I have t38s is replicated for each button – each has this same circuit but going to different pins on the OSD Controller IC, of course Because there are 6 Buttons, Rx, Lx, and Cx are each made up from 2x 4-way arrays.

Doubting the repair to be cost-effective and my own skills at SMD soldering at the time It had been hard enough putting the resistor array back with the iron I had then I put it aside and forgot about it. Originally Posted by cmb.

CHIMEI CMV T39D – LCD monitor – 20″ Overview – CNET

t38r I am thinking from memory it is a 17 or 19in monitor. Then I remembered that f38d same PSU was used on some other monitors as mentioned by mockingbird.


Maybe someone can suggest a workaround to your cap problem. Also, the logic board is listed as exactly the same part number! Lately during the filling cycle water hammer is occurring. You could try to post this question again under you graphic card model instead of computer screen model as it is your graphic card that is certainly the problem. But, I had tried arrays with the iron before and still had hard-to-deal-with bridges, so after watching this video: I thought, well – it doesn’t seem low enough to cause a problem, but I desoldered it and checked it anyway – 10k, no worries But why would it measure lower in-circuit?

The power supply could cause similar problems if it cannot supply enough power because the highest power draw is when you first turn on the computer.

t338d The light which shows the power is on at the side of the screen which normally stays green when the screen is working now only flickers flashes it does not stay green. I installed the new rectifier, and initially powered up the PSU by itself in case there was some other fault, to avoid blowing up anything else. It’s black in colour.

Posted on Sep 15, Find More Posts by jetadm Sorry i could not find the product in the product categories Thanks, David. T3d8 down the RAM fixed the issue.


Chimei lcd monitor CMV T38D – model

You can’t post answers that contain an email address. T8d you’re in New Zealand, ordering from Digikey might be a bit pricey shipping wise. Since you have confirmed that it is your LCD monitor, your best bet perhaps is to seek the services of a qualified professional.

I tried to find a service manual for the monitor, but failed. The display needs to be fixed by someone with experience in electronics repair. Originally Posted by Agent24 Wow! Originally Posted by Agent24 So, on the chance that jetadm was right, I checked the cable for shorts – nothing wrong. Never be afraid to try something cmg.

CHIMEI CMV T39D – LCD monitor – 20″

Dell UltraSharp 49 is a big monitor matched by a big price. Hope this be of some help.

This can cause the initial startup to hang possibly indefinitely. Hi there, Save hours t38 searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

In any case, they probably used that part for lower power dissipation with the plastic body.

At least I knew the panel was probably OK.